1. pl
  2. en
  3. it

ABYC vs ISO 13297: comparing the standards for yacht electrical systems

20 November 2026
Listing, damaged wreck of a boat at the quay – the result of missing technical care and inspections.

On boats in Europe you will meet two main sets of standards for electrical installations: the European ISO 13297, which the CE mark is based on, and the American ABYC standards. Both aim for the same thing: an installation that does not catch fire, does not give shocks and works reliably at sea. But they describe it in different ways.

 

My experience tells me one thing: ABYC says much more precisely what to do and how to do it. It gives concrete distances, values, test procedures and exceptions, often explaining the reasoning too. ISO 13297 more often states a requirement in general terms and leaves the details to the installer.

 

Here are a few concrete examples from practice.

 

The two standards in brief

 

ISO 13297:2020 (in Europe EN ISO 13297:2021) covers AC and DC installations on small craft up to 24 m. It replaced the earlier ISO 10133. It is harmonised with Directive 2013/53/EU, so yards building CE-marked boats base their electrical installations on it. The whole standard runs to a few dozen pages.

 

ABYC (American Boat & Yacht Council) is a US organisation that has been writing standards for boats since the 1950s. Electrical systems are covered by a whole series of separate standards:

 

  • E-11: AC and DC electrical systems, latest edition 2025,
  • E-10: storage batteries,
  • E-13: lithium-ion batteries,
  • C-7: battery switches,
  • A-31: battery chargers and inverters.

 

E-11 on its own is more than twice the length of the whole of ISO 13297, and batteries and switches have their own standards on top. That alone shows the difference in approach.

 

Example 1: Battery mounting

 

ISO 13297 (clause 8.2): once installed, a battery must not move more than 10 mm in any direction under a force equal to twice its weight.

 

ABYC E-10: the same idea of a force of 2× the battery's weight, but the permitted movement is 25 mm. In return, ABYC describes exactly how to carry out the test:

 

  • the force is applied through the battery's centre of gravity,
  • for one minute,
  • separately in each direction: vertical, fore-and-aft and athwartships.

 

On top of that, for lithium batteries ABYC E-13 requires no visible movement where the manufacturer gives no guidance. For offshore boats it also takes knockdowns and hull slamming into account.

 

Takeaway: ISO has the stricter value, but ABYC tells you unambiguously how to check it. A good installer takes the 10 mm from ISO and the test procedure from ABYC.

 

Example 2: Battery terminals

 

ISO 13297 says very little about terminals:

 

  • cable terminals must not depend on spring pressure (clause 8.8),
  • metal objects must not be able to touch the terminals by accident (clause 8.4).

 

ABYC E-10 gives concrete rules you can check at every inspection:

 

  • no more than 4 terminals on one battery post,
  • the terminal of the cable with the highest ampacity closest to the battery, then the smaller ones,
  • no wing nuts for cables of 6 AWG (13.3 mm²) and larger,
  • flat washers only directly under the lock washer and nut, never between terminals,
  • a soldered-only terminal, without crimping, is allowed only if the solder joint is at least 1.5 times the cable diameter long,
  • cables connected only to the terminals provided by the battery manufacturer,
  • no spring clips or temporary connections such as crocodile clips.

 

Takeaway: ISO tells you the connection has to be good. ABYC tells you exactly what it should look like.

 

Example 3: Batteries and the fuel system

 

ISO 13297 (clauses 8.6–8.7): a battery must not be installed directly above or below a fuel tank or fuel filter without a separating structure. Metal fuel-system components within 300 mm above the battery must be electrically insulated.

 

ABYC E-10: batteries must not be installed above or below a fuel tank, fuel filter or fuel fitting. The zone is 305 mm from the plane of the battery terminals, horizontally and vertically. ABYC adds clarifications that settle the usual doubts:

 

  • a continuous fuel line without fittings may run above or below the battery,
  • a terminal boot or battery cover is not enough as protection, because they are removed during maintenance,
  • the shielding can be any non-conductive material that can withstand a blow from a tool.

 

Takeaway: the values are almost the same, but only ABYC answers the questions an electrician actually asks on board.

 

Example 4: The fuse at the battery

 

Here both standards are equally precise, which shows that ISO can be specific too:

 

  ISO 13297 (clause 12.1) ABYC E-11
Fuse from the power source, measured along the cable 175 mm 178 mm (7 in)
Sheathed cable, from the battery terminal up to 1.8 m up to 183 cm (72 in)
Sheathed cable, from another source up to 1 m up to 102 cm (40 in)
Starter motor cables exempt exempt

 

The difference is in the detail. The 2025 edition of ABYC E-11 lists the self-limiting devices by name that need no fuse at their output: alternators, battery chargers, DC/DC converters, solar panels, wind generators and fuel cells. It also gives the condition: the cable's ampacity must be at least equal to the device's rated output.

 

Example 5: Fuse interrupting capacity

 

This is the biggest difference between the two standards.

 

ISO 13297 requires in general terms that the protection interrupts an overcurrent before the cable insulation overheats. It does not say what short-circuit current the fuse must be able to interrupt.

 

ABYC E-11 (2025) is very specific:

 

  • if the battery manufacturer does not state the short-circuit current, use 3,000 A per 100 Ah for lead-acid batteries and 5,000 A per 100 Ah for lithium,
  • the ampere interrupting capacity (AIC) of the main fuse must be at least equal to that current,
  • parallel banks above 500 Ah need an additional fuse at each battery,
  • the requirements also apply to branch-circuit fuses, except small ones, for example up to 30 A at 12 V.

 

A 300 Ah LiFePO4 bank works out at around 15,000 A of short-circuit current. ISO will not tell you that your fuse may be unable to interrupt it. With ABYC you can work it out in a minute.

 

Example 6: The battery switch

 

ISO 13297 (clause 9.2) and ABYC E-11 agree that the switch's 30-second rating must be at least equal to the starter motor current, and its continuous rating must match the protection downstream.

 

ABYC, however, has a separate standard, C-7, that describes the switch itself:

 

  • four current ratings permanently marked on the switch: continuous, 5-minute, 30-second and switching,
  • a mandatory marking if the switch is not suitable for the starting circuit,
  • no aluminium in current-carrying parts,
  • spacing between live parts: 12.7 mm through air and 19.1 mm over surface,
  • tests at −30°C and +60°C, vibration, 5,000 shocks at 10 g, and up to 5,000 operations under load.

 

ISO, on the other hand, has two requirements that ABYC does not have in this form. A battery switch is required for practically every battery, and a remote-controlled switch must also allow manual operation.

 

Example 7: Lithium batteries

 

ISO 13297 does not cover lithium batteries at all; they have a separate standard, ISO 23625.

 

ABYC E-13 describes lithium installations in great detail, including:

 

  • a battery switch independent of the BMS for installations above 500 Wh,
  • the conditions under which a BMS contactor may serve as the battery switch,
  • the requirement to design the system so that a BMS disconnecting the battery does not damage other equipment, with a description of alternator voltage spikes and ways to protect against them,
  • storing the battery within the limits set by the manufacturer,
  • the manufacturer's duty to state the short-circuit current in the event of a BMS failure.

 

Where is ISO stricter?

 

To keep the comparison fair: ISO 13297 is sometimes stricter in its values.

 

Topic ISO 13297 ABYC
Battery movement in the force test 10 mm 25 mm
When a battery switch is required practically always above 800 CCA or 100 Ah (lithium: 500 Wh)
Equipment connected ahead of the switch each with its own fuse close to the battery permitted
Heel no electrolyte leakage up to 30°; on sailing monohulls, electrolyte containment up to 45° recommendation on battery orientation
Remote battery switch must also have manual operation status visible at the control

 

How I use this in practice

 

My rule for refits is simple:

 

  1. I comply with ISO 13297, because conformity with the directive and the CE mark are based on it.
  2. I carry out the work to ABYC's level of detail, because that is where it is described exactly how to do it well.
  3. Where the standards differ, I choose the stricter requirement.

 

The result is an installation that stands up to any surveyor or insurer, whichever standard they assess it against. Above all, it is simply safer.

 

I cover each of these examples in more depth in separate articles on the blog:

 

  • Battery mounting on a yacht: 10 mm or 25 mm?
  • Battery terminals: the 5 most common mistakes
  • The fuse at the battery: the 175 mm rule
  • Fuses for LiFePO4 batteries: why a standard fuse may not interrupt a short circuit
  • The battery switch: when it is required and how to choose one

 

Want the installation on your boat checked against both standards? I am an ABYC member and work to the ABYC standards and EN ISO 13297. Write or call me, including on WhatsApp: +39 351 384 9089 or +48 791 74 74 54.

 

Grzegorz Szubert, Yacht Electrical Services, ABYC member

Logo marki Grzegorz Szubert – Nie Tylko Elektryka Jachtowa.
Logo ABYC Member – American Boat and Yacht Council, standardy bezpieczeństwa jachtowego.

kontakt@grzegorzszubert.pl

tel. +48 791 74 74 54

tel. +39  351 384 9089

Yacht Electrical Services - Grzegorz Szubert

Viale Centrale, 13,

09012 La Maddalena CA

Profil na Instagramie - Grzegorz Szubert
Profil na Facebooku - Elektryka Jachtowa
Logo marki ElektrykaJachtowa.pl.

Client area · Online work order · Privacy & cookies · This site is protected by reCAPTCHA and is subject to the Privacy Policy and Terms of Service of Google.