1. pl
  2. en
  3. it

Fuses for LiFePO4 batteries: why a standard fuse may not interrupt a short circuit

20 November 2026
Listing, damaged wreck of a boat at the quay – the result of missing technical care and inspections.

You switch to LiFePO4, install a 300 Ah bank and fit a 250 A fuse at the battery. Everything looks right: the fuse is close to the terminal and its rating suits the cable. But in a short circuit that fuse may not stop the current. The fuse element melts, an electric arc forms inside, and it keeps burning until something melts or bursts.

 

In this article I explain why that happens, how to work it out, and what ABYC E-11 says in its 2025 edition, which brought important changes here. It is rarely discussed in Europe, because the European standard ISO 13297 does not cover it in detail. You can read more about the differences between the standards in ABYC vs ISO 13297: comparing the standards.

 

Two different fuse ratings

 

Every fuse has two important ratings that are easy to confuse:

 

  • The current rating, for example 250 A. It says at what current the fuse operates. You choose it to suit the cable's ampacity.
  • The ampere interrupting capacity (AIC), for example 10,000 A. It says the highest short-circuit current the fuse can safely interrupt.

 

If the short-circuit current is higher than the interrupting capacity, the fuse cannot deal with the arc that forms as its element melts. The result can be current still flowing through the arc, a burst fuse body and a fire.

 

The current rating is always printed on the fuse. The interrupting capacity usually has to be looked up in the manufacturer's data sheet.

 

How much current does a battery short circuit deliver?

 

Short-circuit current depends on the battery's internal resistance. Lithium batteries, LiFePO4 included, have very low internal resistance, so in a short circuit they deliver an enormous current, far more than a lead-acid battery of the same capacity.

 

ABYC E-11 (2025 edition, clause 11.10.1.3.2) says that where the manufacturer does not state the battery's short-circuit current, it is calculated as follows:

 

Battery type Short-circuit current per 100 Ah
Lead-acid (other than TPPL) 3,000 A (3 kA)
Lithium-ion, LiFePO4 included, and TPPL lead-acid 5,000 A (5 kA)

 

TPPL batteries are lead-acid batteries with thin plates of pure lead. Their internal resistance is low, so the standard treats them like lithium.

 

If the manufacturer does state the short-circuit current, use their figure. E-13 in fact requires the maker of a lithium battery to state in its documentation the maximum short-circuit current in the event of a BMS failure.

 

Worked examples

 

  • LiFePO4 100 Ah → about 5,000 A
  • LiFePO4 200 Ah → about 10,000 A
  • LiFePO4 300 Ah → about 15,000 A
  • 2 × 200 Ah LiFePO4 in parallel → about 20,000 A
  • 4 × 100 Ah AGM in parallel → about 12,000 A

 

Series or parallel?

 

In parallel, the batteries' short-circuit currents add up. In series they do not. The standard gives an example that shows this well: six 6 V batteries wired into a 12 V bank (three strings of two batteries in series) have a short-circuit current three times that of one battery, not six times.

 

What changed in ABYC E-11 in 2025?

 

The previous edition treated all batteries in much the same way. The new one draws a clear line.

 

1. Flooded lead-acid batteries up to 2,200 CCA or 500 Ah

 

The minimum interrupting capacity of the main fuse is read from a table in the standard, according to battery size and system voltage. For example, in a 12 V system with a lead-acid bank of up to 140 Ah, the main fuse needs an interrupting capacity of at least 1,500 A.

 

2. All other chemistries and large lead-acid banks

 

This covers LiFePO4 and other lithium batteries, AGM, gel, TPPL, and lead-acid banks above 2,200 CCA or 500 Ah. The main fuse's interrupting capacity must be:

 

  • at least equal to the short-circuit current stated by the battery manufacturer, or
  • if that is unknown, calculated at 3 kA or 5 kA per 100 Ah, or
  • 20 kA at 125 V DC or higher, if the short-circuit current exceeds 20 kA.

 

3. An extra fuse at each battery in large banks

 

Parallel banks above 500 Ah need an additional fuse between each battery and the main fuse, meeting the same interrupting capacity requirements. It is a safety fuse, fitted in addition to the main one.

 

4. Branch circuit fuses

 

The interrupting capacity requirements now also cover branch circuit fuses. Small devices are the exception: up to 30 A at 12 V, 15 A at 24 V, 10 A at 36 V and 7.5 A at 48 V, as are solid-state (electronic) protection devices.

 

Voltage matters

 

The standard points out that a fuse manufacturer's interrupting capacity applies to a specific voltage and usually falls as the voltage rises. A fuse that interrupts 10 kA at 12 V may interrupt much less at 48 V. On 24 V and 48 V systems this needs checking with particular care.

 

What if no fuse is enough?

 

ABYC E-13 for lithium batteries is clear: if necessary, the bank must be subdivided into smaller units so that the interrupting capacity of the protection devices is not exceeded. In practice that means several smaller banks, each with its own fuse.

 

What does ISO say?

 

The European standard ISO 13297 requires in general terms that protection interrupts an overcurrent before the cable insulation overheats, and that it is coordinated with the circuit. It does not say what short-circuit current the fuse must be able to interrupt, or how to work it out. Lithium batteries are covered by a separate standard, ISO 23625.

 

For lithium installations it is therefore worth turning to ABYC, which says exactly what to calculate and which fuse to use.

 

Which fuses have a high interrupting capacity?

 

The fuses commonly used on boats vary widely in interrupting capacity. The highest is usually found in Class T fuses, designed specifically to protect large battery banks; their interrupting capacity typically reaches 20 kA. Other popular types, mounted directly on the terminal or in fuse holders, often have a much lower interrupting capacity. I always check the data sheet for the specific fuse, at the specific system voltage.

 

What to check in your installation

 

  1. Find the short-circuit current in the battery documentation. If it is not there, allow about 5 kA per 100 Ah for lithium and 3 kA for lead-acid.
  2. Add up the short-circuit currents of batteries connected in parallel.
  3. Check the main fuse's data sheet for its interrupting capacity at your system voltage.
  4. If the interrupting capacity is lower than the short-circuit current, replace the fuse with a type that has a higher interrupting capacity.
  5. With a bank above 500 Ah, check that each battery has its own fuse.
  6. Check the branch circuit fuses above 30 A (at 12 V) too.

 

Summary

 

Requirement ISO 13297 ABYC E-11 (2025)
Main fuse interrupting capacity no detailed requirements from a table (flooded lead-acid) or from short-circuit current (others)
Short-circuit current if not stated by the manufacturer not defined 3 kA/100 Ah lead-acid, 5 kA/100 Ah lithium and TPPL
Fuse at each battery no in parallel banks above 500 Ah
Branch circuits no requirements above 30 A at 12 V
Subdividing the bank no E-13: if interrupting capacity is not enough

 

Planning a switch to LiFePO4, or want your existing installation checked? I will work out your bank's short-circuit current and choose protection to ABYC E-11 and E-13. Write or call me, including on WhatsApp: +39 351 384 9089 or +48 791 74 74 54.

 

Grzegorz Szubert, Yacht Electrical Services, ABYC member

Logo marki Grzegorz Szubert – Nie Tylko Elektryka Jachtowa.
Logo ABYC Member – American Boat and Yacht Council, standardy bezpieczeństwa jachtowego.

kontakt@grzegorzszubert.pl

tel. +48 791 74 74 54

tel. +39  351 384 9089

Yacht Electrical Services - Grzegorz Szubert

Viale Centrale, 13,

09012 La Maddalena CA

Profil na Instagramie - Grzegorz Szubert
Profil na Facebooku - Elektryka Jachtowa
Logo marki ElektrykaJachtowa.pl.

Client area · Online work order · Privacy & cookies · This site is protected by reCAPTCHA and is subject to the Privacy Policy and Terms of Service of Google.