1. pl
  2. en
  3. it

Battery mounting on a yacht: 10 mm or 25 mm? ISO 13297 and ABYC requirements

20 November 2026
Listing, damaged wreck of a boat at the quay – the result of missing technical care and inspections.

A battery is one of the heaviest things on board. A 100 Ah lead-acid battery usually weighs 25–30 kg, and a whole bank on a cruising yacht easily tops 100 kg. While the boat sits in the marina, nobody gives it a thought. But one short, steep wave, a hull slamming into the water or a knockdown is enough to set that mass moving.

 

A loose battery is not just a risk to the joinery. As it moves it drags its cables, which can pull out of the terminals or touch metal parts. Then you have a short circuit carrying thousands of amps, in a cramped compartment, often right next to the fuel system.

 

That is why both main standards for yacht electrical systems, the European ISO 13297 and the American ABYC, set concrete, measurable requirements for battery mounting. In this article I compare them and show how they work in practice. You can read more about the standards themselves in ABYC vs ISO 13297: comparing the standards.

 

The force test: twice the battery's weight

 

Both standards use the same idea. A force equal to twice the battery's weight is applied to the installed battery, and you check how far it moves. For a 25 kg battery that is a force of about 50 kg.

 

What differs is the permitted movement:

 

  ISO 13297 (clause 8.2) ABYC E-10
Force 2× battery weight 2× battery weight
Direction any vertical, fore-and-aft, athwartships
Permitted movement 10 mm 25 mm
Duration of force not stated 1 minute in each direction
Trailering to be taken into account not mentioned

 

ISO is more than twice as strict here. ABYC, on the other hand, describes exactly how to carry out the test: the force is applied through the battery's centre of gravity, for one minute, separately in each direction: vertically, fore and aft along the boat's centreline, and to starboard and port.

 

On refits I take the 10 mm value from ISO and the test method from ABYC. That way the installation meets both standards.

 

Why twice the weight?

 

A force equal to twice the weight corresponds to an acceleration of about 2 g. Loads like that can occur when the bow slams hard into a wave, on a fast motorboat running over a short chop, or in a sudden heel. Offshore they can be higher, which is why the standard goes further for lithium batteries (more on that below).

 

How to check it on board

 

Nobody carries a force gauge, but a simple test is easy:

 

  1. Grip the battery with both hands and try hard to move it in every direction, upwards included.
  2. If there is any visible movement of the battery relative to the tray, or of the tray relative to the structure, the mounting will not meet ISO.
  3. Pay attention to vertical movement. Many mountings hold the battery sideways but do nothing to stop it lifting.

 

Heel and electrolyte

 

On a sailing yacht a battery spends long hours heeled over. Here ISO 13297 (clause 8.3) is specific:

 

  • batteries must withstand heel up to 30° without electrolyte leaking,
  • on sailing monohulls any spilled electrolyte must also be contained at up to 45° of heel.

 

ABYC E-10 approaches it differently:

 

  • it requires provision to contain leakage and spillage of electrolyte, for example with a box or tray,
  • it recommends taking into account the battery type (liquid or immobilised electrolyte) and the type of boat (heel on a sailboat, acceleration on a powerboat),
  • it recommends orienting flooded batteries on sailboats so that heeling uncovers the plates as little as possible,
  • it requires that fasteners for the battery box or tray are kept clear of the area where spilled electrolyte collects,
  • it requires mounting materials and surfaces that may contact the electrolyte to withstand electrolyte attack.

 

I often see that last one ignored: a lead-acid battery sitting straight on plywood that, after a few seasons, has been eaten by acid, with the strap screws rusted through.

 

LiFePO4 batteries: no visible movement

 

For lithium batteries ABYC E-13 is stricter still:

 

  • the battery manufacturer's recommendations come first, and the standard points out that they may be stricter than the requirements for lead-acid batteries,
  • if the manufacturer gives none, the battery must be secured so that there is no visible movement in the conditions the boat is intended to operate in,
  • for offshore boats those conditions should include knockdowns and slamming loads.

 

Why so strict? Mechanical damage to a lithium cell is one of the causes of thermal runaway. A fire like that cannot be put out quickly, and the gases the cells release are toxic and flammable.

 

On the other hand, E-13 notes that lithium batteries do not routinely release gas or leak electrolyte, so the requirements for an electrolyte tray and hydrogen ventilation do not apply to them. The mounting, however, has to be very rigid.

 

A common mistake on refits: the LiFePO4 is dropped into the old lead-acid battery's place, in the same box and with the same straps. A lithium battery of the same capacity is usually much lighter and differently sized, so the old mounting no longer holds it.

 

Where to install the battery

 

ISO 13297 adds a few rules on location (clauses 8.1 and 8.5):

 

  • the battery must be permanently installed, in a dry, ventilated place,
  • above the anticipated bilge water level,
  • protected from mechanical damage where it is installed or by its enclosure.

 

On top of that come the distances from the fuel system, which I cover in a separate article Batteries and the fuel system.

 

With lithium batteries temperature matters too. ABYC E-13 requires the battery to be installed where temperatures stay within the manufacturer's limits, and recommends avoiding external heat sources. The engine compartment is usually ruled out.

 

The most common mistakes I see on board

 

  1. A battery "held" by its own weight or wedged with a piece of wood. At the first serious heel it ends up in the bilge.
  2. Bungee cords, rope and Velcro. They stretch, age in sun and damp, and pass no standard's force test.
  3. A strap through a plastic box with no rigid base, screwed into plywood that has been soaking up water for years.
  4. Nothing holding it down vertically. The battery sits in a frame that stops it sliding sideways, but nothing stops it jumping upwards.
  5. Corroded screws and brackets, fitted exactly where electrolyte collects.
  6. A LiFePO4 in the old lead-acid box, with several centimetres of play.

 

What good mounting looks like

 

  • A rigid tray or frame bolted to the boat's structure, not to thin joinery.
  • For lead-acid batteries, an acid-resistant tray with a raised edge that will hold spilled electrolyte.
  • Straps of adequate strength with steel buckles, or a rigid hold-down bar across the top of the battery.
  • Restraint in every direction, upwards included.
  • Batteries in a bank pressed together, with no gaps.
  • Stainless steel fittings, kept out of the electrolyte zone.

 

Summary

 

Requirement ISO 13297 ABYC
Movement under 2× weight 10 mm 25 mm (E-10)
Lithium batteries no specific requirements no visible movement, manufacturer's guidance (E-13)
Heel without leakage 30°; on sailboats, containment up to 45° protection against leakage, orientation recommended
Location dry, ventilated, above bilge water ventilation, electrolyte resistance, temperature (lithium)

 

Not sure whether your batteries are secured to the standards? I can check it during an installation survey, or design new mounting when you switch to LiFePO4. Write or call me, including on WhatsApp: +39 351 384 9089 or +48 791 74 74 54.

 

Grzegorz Szubert, Yacht Electrical Services, ABYC member

Logo marki Grzegorz Szubert – Nie Tylko Elektryka Jachtowa.
Logo ABYC Member – American Boat and Yacht Council, standardy bezpieczeństwa jachtowego.

kontakt@grzegorzszubert.pl

tel. +48 791 74 74 54

tel. +39  351 384 9089

Yacht Electrical Services - Grzegorz Szubert

Viale Centrale, 13,

09012 La Maddalena CA

Profil na Instagramie - Grzegorz Szubert
Profil na Facebooku - Elektryka Jachtowa
Logo marki ElektrykaJachtowa.pl.

Client area · Online work order · Privacy & cookies · This site is protected by reCAPTCHA and is subject to the Privacy Policy and Terms of Service of Google.