1. pl
  2. en
  3. it

The battery switch on a yacht: when it is required, how to size it and what ratings it needs

20 November 2026
Listing, damaged wreck of a boat at the quay – the result of missing technical care and inspections.

The battery switch is the most important switch in the whole installation. All the current from the batteries flows through it, starter current included, and in a fire or short circuit it is the thing that has to cut the power. Yet it is often chosen by eye, and on many boats the same switch has been working for years, with burnt contacts and no markings at all.

 

In this article I go through what ISO 13297, ABYC E-11, ABYC E-13 (lithium batteries) and ABYC C-7, a separate standard covering the switch itself, say about battery switches. You can read more about how ABYC and ISO differ in ABYC vs ISO 13297: comparing the standards.

 

When is a battery switch required?

 

Here the standards clearly differ.

 

ISO 13297 (clause 9.1) requires a battery switch practically always. The only exception is a boat with an outboard engine that has nothing but engine starting and navigation light circuits.

 

ABYC E-11 (2025 edition, clause 11.6.1.2.1) requires one for a battery or bank rated above 800 CCA, or, where CCA is not available, with a capacity above 100 Ah.

 

ABYC E-13 covers lithium batteries in systems above 500 Wh, which is from about 40 Ah at 12 V. In such a system each battery or bank needs a battery switch or other means of disconnection independent of the BMS.

 

In practice, on any boat with a house system, both standards will require a battery switch anyway.

 

Where should it go?

 

Both standards say much the same:

 

  • the switch goes in the positive conductor, in a system with a grounded negative,
  • as close as practicable to the battery,
  • in a readily accessible location.

 

ABYC E-11 distinguishes two levels here. The switch itself must be accessible, and its control, whether built in or remote, must be readily accessible, meaning it can be reached quickly and safely in an emergency.

 

In an isolated DC system, where neither pole is connected to ground, both standards require the switch to open the positive and negative simultaneously. ABYC allows one exception: if both conductors have their own overcurrent protection, a switch in the positive is enough.

 

What may be connected ahead of the switch?

 

Both standards allow some equipment to be fed straight from the battery, bypassing the switch:

 

  • bilge pumps, alarms and CO detectors,
  • electronics with continuously powered memory,
  • charging equipment such as chargers, solar panels and wind generators,
  • the engine compartment blower,
  • under ABYC, also impressed current systems and constant power to the propulsion ECU.

 

One important difference: ISO requires each of these devices to have its own fuse as close as possible to the battery terminal.

 

A practical point: with the main switch off, this equipment still draws current. If you leave the boat for the winter or for a few weeks, check what is permanently connected.

 

How to size the switch

 

Here ABYC E-11 (clause 11.6.1.2.5) and ISO 13297 (clause 9.2) say the same thing:

 

  1. The 30-second rating, the starting rating, must not be less than the maximum cranking current of the largest starter motor it serves.
  2. The continuous rating must be at least the total ampacity of the main overcurrent protection devices connected after the switch, or the ampacity of the feeder cable to the switch, whichever is less.

 

Example: after the switch there are two main fuses, 100 A and 150 A, and the feeder cable has an ampacity of 200 A. The lower of 250 A and 200 A is 200 A, so the switch needs a continuous rating of at least 200 A.

 

What ratings does the switch itself need? ABYC C-7

 

ABYC C-7 describes how a manufacturer must build and test a battery switch for up to 60 V. The 2025 edition of E-11 explicitly requires battery switches to comply with it, and E-13 does the same for lithium installations.

 

Four current ratings

 

A switch that complies with C-7 has these permanently marked on it:

 

  • the continuous rating: how much it can carry indefinitely,
  • the 5-minute rating: for example while a windlass or bow thruster runs,
  • the 30-second rating, the starting rating,
  • the switching rating: how much current it can safely interrupt.

 

If a switch has no starting rating, it must carry a marking saying it must not be used in the starting circuit. A bare "300 A" on the case tells you nothing.

 

Construction

 

  • Current-carrying parts of copper, copper alloy or another corrosion-resistant metal. Aluminium is not allowed.
  • Housing and handle made of self-extinguishing material.
  • Tightening the cables must not loosen the internal connections.
  • Between bare live parts of opposite polarity at least 12.7 mm through air and 19.1 mm over surface, or an insulating barrier.
  • Positions that are clearly felt and clearly marked.

 

Environmental protection

 

  • Where it may be flooded, the switch must be watertight (IP67).
  • Where rain and spray reach, at least IP54.
  • In compartments with petrol engines, the marking "Ignition Protected".

 

The tests it has to pass

 

  • 24 hours at −30°C, then operation and a 1-metre drop,
  • 24 hours at +60°C,
  • 12 hours of vibration and 5,000 shocks at 10 g,
  • from 1,000 to 5,000 operations under load, depending on current; afterwards, the voltage drop across the contacts may rise by no more than 35%,
  • a 500 V insulation test.

 

What the instructions must contain

 

Among other things, the manufacturer must state the terminal tightening torque, the minimum cable size, the operating temperature range, the ingress protection rating and whether the switch may be operated under load. It must also warn that interrupting a current above the switching rating may damage the switch, and that continuing to use it may be dangerous.

 

C-7 has only existed since 2021, so most battery switches on older boats have never been through tests like these.

 

Remote battery switches

 

More and more boats have battery switches operated by a button on the panel. The standards treat them differently:

 

  • ABYC C-7: the switch's status must be visible at the control.
  • ISO 13297 (clause 9.3): a remote switch must also allow safe manual operation.

 

The ISO requirement makes sense. If the control supply or the button itself fails, you still have to be able to cut the battery off. When I choose a remote switch, I check that it has a lever or knob for manual operation.

 

LiFePO4: the battery switch is not the BMS

 

For lithium batteries ABYC E-13 requires a battery switch independent of the BMS, in addition to the output disconnect device the BMS controls. The BMS contactor may serve as the battery switch only if:

 

  • it is a mechanical contactor, not a solid-state device,
  • it is normally open and closes only when energised,
  • its energising power is interrupted directly by a remote switch mounted in a readily accessible location.

 

Watch out for classic 1–2–BOTH switches too. Connecting two lithium banks at different voltages can cause a huge paralleling current. E-13 warns that ordinary manual switches may not be suitable, and requires a means of preventing overcurrent when batteries are connected in parallel.

 

There is one more issue: turning the switch off while the alternator is charging can cause a voltage spike that damages electronics. I cover this in Voltage spikes when a BMS disconnects a LiFePO4 battery and Battery switch with the engine running.

 

How to check your battery switch

 

  1. Look at the case. Are all four current ratings there? If there is only one number, the switch does not comply with C-7.
  2. Check the temperature. After a long run under load the terminals should not feel noticeably warm.
  3. Measure the voltage drop across the switch with loads switched on. A drop that keeps growing means worn contacts.
  4. Look at the terminals on the back. Discolouration, a melted housing or green deposits mean it is time to replace it.
  5. Check access. In a fire, can you reach the switch quickly, without opening several lockers?

 

Summary

 

Requirement ISO 13297 ABYC
When required practically always above 800 CCA or 100 Ah (E-11); lithium above 500 Wh (E-13)
30-second rating ≥ starter current ≥ starter current
Continuous rating ≥ downstream protection or feeder cable the same
Equipment ahead of the switch permitted, each with its own fuse permitted
Remote switch must have manual operation status visible at the control
Switch construction and tests no separate standard ABYC C-7
LiFePO4 no specific requirements switch independent of the BMS (E-13)

 

Want your battery switch checked or replaced? I will choose a switch to suit your installation, including when you move to LiFePO4. Write or call me, including on WhatsApp: +39 351 384 9089 or +48 791 74 74 54.

 

Grzegorz Szubert, Yacht Electrical Services, ABYC member

Logo marki Grzegorz Szubert – Nie Tylko Elektryka Jachtowa.
Logo ABYC Member – American Boat and Yacht Council, standardy bezpieczeństwa jachtowego.

kontakt@grzegorzszubert.pl

tel. +48 791 74 74 54

tel. +39  351 384 9089

Yacht Electrical Services - Grzegorz Szubert

Viale Centrale, 13,

09012 La Maddalena CA

Profil na Instagramie - Grzegorz Szubert
Profil na Facebooku - Elektryka Jachtowa
Logo marki ElektrykaJachtowa.pl.

Client area · Online work order · Privacy & cookies · This site is protected by reCAPTCHA and is subject to the Privacy Policy and Terms of Service of Google.