1. pl
  2. en
  3. it

The fuse at the battery on a yacht: the 175 mm rule in ISO 13297 and ABYC E-11

20 November 2026
Listing, damaged wreck of a boat at the quay – the result of missing technical care and inspections.

The cable from the battery to the battery switch and the distribution panel is the most dangerous cable on board. If there is no fuse right at the battery, a short circuit on that run means thousands of amps. Nothing will stop it until the cable itself burns through, and before that happens the insulation has time to catch fire.

 

That is why both main standards, ISO 13297 and ABYC E-11, speak with practically one voice here and give exact distances. It is one of the few topics where the European standard is just as precise as the American one. You can read more about both standards in ABYC vs ISO 13297: comparing the standards.

 

The basic rule: 175 mm from the source

 

  ISO 13297 (clause 12.1 a) ABYC E-11 (clause 11.10.1.1.1.1)
Fuse from the power source no more than 175 mm no more than 178 mm (7 in)
How to measure along the cable along the cable

 

The key point is that the distance is measured along the cable, not in a straight line. A fuse mounted "right next to" the battery but reached by half a metre of cable looping round does not meet the standard.

 

ABYC talks about the distance from the source of power or other point of connection. So the rule applies not only to the battery terminal but also, for example, to a busbar that feeds further circuits.

 

ABYC also requires the fuse to be accessible. A fuse permanently built in behind a panel, reachable only with tools, does not meet that requirement.

 

The exceptions worth knowing

 

Both standards allow a greater distance only in specific cases:

 

Situation ISO 13297 ABYC E-11
Cable sheathed along its entire length, connected to the battery terminal as close as practicable, no more than 1.8 m as close as practicable, no more than 183 cm (72 in)
Sheathed cable connected to a source other than the battery no more than 1 m no more than 102 cm (40 in)
Starter motor cables exempt exempt
Cables shorter than 175 mm (ABYC: 178 mm) exempt exempt
Alternator with integral regulator, cable < 1 m and sheathed, not to the battery exempt exempt

 

In both standards "sheathed" means, for example, conduit, a junction box, a control box or an enclosed panel, and it has to be along the cable's entire length. A cable that runs loose through the bilge for part of its route cannot use this exception.

 

Self-limiting devices (ABYC 2025)

 

The 2025 edition of ABYC E-11 extends the alternator exception to all self-limiting devices and lists them by name: alternators, battery chargers, DC/DC converters, solar panels, wind generators and fuel cells. No fuse is required at their output if the cable's ampacity is at least equal to the device's rated output.

 

Note: the exception applies to the device's output. The other end of the same cable, connected to the battery, still needs a fuse at the battery, because from that side it is the battery that feeds the short circuit.

 

Isolated systems

 

In an isolated system, where neither pole is connected to ground, both conductors, positive and negative, are ungrounded and both need protection. ABYC allows one exception: if the battery switch opens the positive and negative simultaneously, the fuse is needed only in the positive up to the switch.

 

Chargers and alternators are power sources too

 

This is a common mistake. The cable from the charger to the battery has a fuse at the battery, but the charger can also feed a short circuit from the other end.

 

ISO 13297 (clause 12.3) requires additional protection for cables from a charger, alternator or other charging source. The protection must be in the device itself or within 1.8 m of it, sized to the device's maximum output. Self-limiting devices are the exception.

 

ABYC E-11 handles this through the exception described above: if the device is self-limiting and the cable can carry its full output, no fuse is needed at the output.

 

In practice I fuse both ends of the cable from a charger or solar controller, unless the manufacturer states plainly that the device is self-limiting and I have sized the cable with a margin.

 

Several fuses on one busbar

 

ABYC allows several main fuses to be connected to a common busbar connected directly to the power source. The condition: the combined rating of those fuses must not exceed the ampacity of the cable feeding the busbar. This is a common layout in larger installations, where several circuits leave one bank: bow thruster, windlass, inverter, panel.

 

What rating should the fuse be?

 

The rule is the same in both standards: the fuse protects the cable, not the load. ISO 13297 (clause 12.2) puts it plainly:

 

  • the fuse's current rating must not exceed the ampacity of the smallest cable in the circuit,
  • the fuse's voltage rating must not be lower than the system voltage.

 

ABYC E-11 requires the same for voltage, and in compartments with petrol engines it also requires ignition-protected fuses.

 

Example: if the cable is rated for 100 A, a 150 A fuse "so it stops blowing" means that under overload the cable burns first. If a fuse keeps blowing, look for the cause or for a heavier cable, not for a bigger fuse.

 

And with LiFePO4?

 

With lithium batteries and large banks one more rating matters: the fuse's ampere interrupting capacity (AIC), the highest short-circuit current it can interrupt. A lithium battery can deliver a short-circuit current of more than ten thousand amps, and not every fuse can cope with that. I cover it in a separate article Fuses for LiFePO4 batteries.

 

What I see most often on board

 

  1. No fuse at all between the battery and the switch or panel.
  2. A fuse mounted at the panel, 2–3 metres from the battery, with the cable running loose through the bilge.
  3. A fuse rated higher than the cable's ampacity, fitted after the smaller one "kept blowing".
  4. Cables from solar panels, a charger or a wind generator connected straight to the battery, with no protection at the battery.
  5. An automotive fuse in a circuit whose voltage or short-circuit current exceeds its ratings.
  6. A fuse that is not accessible: built in behind a panel or under a floorboard held down by several screws.

 

Summary

 

Requirement ISO 13297 ABYC E-11
Basic distance 175 mm 178 mm
Sheathed cable from the battery 1.8 m 183 cm
Sheathed cable from another source 1 m 102 cm
Starter motor exempt exempt
Chargers and alternators protection at the source or within 1.8 m, exception for self-limiting devices exception for self-limiting devices if the cable can carry full output
Fuse rating ≤ ampacity of the smallest cable the same
Interrupting capacity (AIC) no detailed requirements detailed requirements, separate for lithium

 

Want the protection on your boat checked? During a survey I measure the distances and check the fuse ratings against the cable sizes. Write or call me, including on WhatsApp: +39 351 384 9089 or +48 791 74 74 54.

 

Grzegorz Szubert, Yacht Electrical Services, ABYC member

Logo marki Grzegorz Szubert – Nie Tylko Elektryka Jachtowa.
Logo ABYC Member – American Boat and Yacht Council, standardy bezpieczeństwa jachtowego.

kontakt@grzegorzszubert.pl

tel. +48 791 74 74 54

tel. +39  351 384 9089

Yacht Electrical Services - Grzegorz Szubert

Viale Centrale, 13,

09012 La Maddalena CA

Profil na Instagramie - Grzegorz Szubert
Profil na Facebooku - Elektryka Jachtowa
Logo marki ElektrykaJachtowa.pl.

Client area · Online work order · Privacy & cookies · This site is protected by reCAPTCHA and is subject to the Privacy Policy and Terms of Service of Google.